Water Decontamination Methods Advantages and Disadvantages

Water Decontamination Methods Advantages and Disadvantages Outline Abstract In Malaysia, for the past many years, drinking water treatment was only limited to water disinfection by using chlorine; however it had been concluded that its use in potable water treatment can be harmful to human health.(Subedi, et al., 2012) Following the development in drinking water treatment, conventional methods in three different technologies are available to have more purified water. They are biological, physicochemical and advanced oxidation process (AOPs) technologies. Each of the technologies has different roles in purifying water and they can be combined to treat drinking water as well. In this assignment, the lists of methods of each technology are stated and some of the main processes are discussed, including the advantages and disadvantages of each of them. For biological technology, slow sand filtration and perchlorate processes are discussed in 3a.For physicochemical technology, coagulation process is discussed in details in 3b. Lastly, the advanced oxidation proces s, AOPs, include both photochemical and non-photochemical oxidation. The fenton system and photocatalytic processes which are categorized in photochemical oxidation are discussed in 3c. Introduction Safe drinking water that free of contaminants is essential to human health and development issue at national, regional and local levels. Its accessibility is human’s rights and a component of effective policy for health protection. (who et al) Therefore, there are many drinking water regulations and acts set by specialized agency such as WHO to have standard on safe drinking water to give awareness to public and thus limit the levels of contaminants. The national primary drinking water regulations and number of regulated contaminants shown in Figure 2.1 and Figure 2.2 in appendix 2.According to the regulations and standards, the characteristics of safe drinking water are contaminants free, natural minerals rich, alkaline pH, taste good and odorless. Firstly, microbiological and chemical contaminants in drinking water may cause acute or chronic health effects or undesirable aesthetic properties when present at excessive concentrations. Microbiological contaminants refer to path ogenic microorganisms such as bacteria, viruses and protozoan parasites. Chemical contaminants refer to toxicity, inorganic and organic chemicals. The other contaminants are pesticides, herbicides and radioactive materials (radionuclide). Besides that, pH of water should be maintained from 6.5 to 8.5. This is because alkaline water is able to neutralize stored acids and help in eliminating toxins. Because of these, various types of technologies of drinking water treatments are introduced to minimize the deleterious effects of contaminated drinking water on human health. Details of contaminants by National Secondary Drinking Water Standards and details of contaminants and potential health effects by National Primary Drinking Water Standards as shown in Figure 2.3 and Figure 2.4 respectively in appendix 2. In the following, three different technologies which are biological, physicochemical and advanced oxidation process (AOPs) are introduced to treat drinking water to a safety level s o that human health is ensured. The goal of all of the developed water treatment technologies is to remove turbidity as well as chemical and pathogenic contaminants from drinking water source in the most affordable and expedient manner possible. 3.Content 3a.Biological Technology Water used for drinking and household use, even water from a ground water supply, should be treated before it is used to ensure it is safe and aesthetically pleasing. One innovative method of water treatment is biological water treatment. Biological drinking water treatment is one technology that has the potential to further many of these objectives. This technology is based on the ability of microorganisms – specifically non-pathogenic bacteria – to efficiently catalyze the biochemical oxidation or reduction of drinking water contaminants and produce biologically stable water. (Snoeyink, 1984) .Biological drinking water treatment is often used in combination with other chemical and chemical processes including ozonation and filtration. There are some types of biological drinking water treatment such as slow sand filtration, rapid biological filtration, ozone-enhanced biological filtration and granular activated carbon biological adsorption. Firstly, the slow sand filtration is a type of centralized or semi-centralized water purification system. A well-designed and properly maintained slow sand filter (SSF) effectively removes turbidity and pathogenic organisms through various biological, physical and chemical processes in a single treatment step. According to (Patrick J. Evans, 2010), slow sand filtration involves very low filtration rates (e.g. 0.04 to 0.10 gpm/ft2) through sand media without pre-oxidation or pre-disinfection (Awwa, 2005). During initial operation of slow sand filtration, a layer of biological matter will be produced on the surface of filter media by the separation of organic matter and other solids. This layer is called as schumutzdecke which acts as the predominant filtering mechanism. It supports the biological matter that works as the primary biofiltration process to remove BDOC, pathogenic microorganisms, and particulates (Page, 2006).To maintenance the slow sand filtration process, periodic scrap ing and removal of the top layer of sand are needed. Besides that, there is another more precise term to replace slow sand filtration which is called biological filtration (SBF) since the biologically active schmutzdecke is an integral part of this process. Besides that, the advantages of slow sand filters is very effective in improving the microbiological and physicochemical qualities of water and it is very easy to operate and maintain. The disadvantages of slow sand filters are vulnerability to clogging when the incoming water is of high turbidity. When dealing with such waters, pre-treatment, such as sedimentation or roughing pre-filtration is required. Next, biological perchlorate or nitrate process. Perchlorate and nitrate have the ability of being anaerobically biodegraded to chloride and nitrogen gas. (Patrick J. Evans, 2010) stated the process involves addition of an electron donor such as acetic acid plus nutrients to water to promote biochemical reduction of biological perchlorate or nitrate process. Moreover, perchlorate and nitrate act as the terminal electron acceptors for respiration by these bacteria. As a result, BPNP vary from the predate biological drinking water treatment processes that are aerobic and employ aerobic bacteria that use oxygen as a terminal electron acceptor for respiration. BPNP can be employed in diverse arrangement including packed beds, fluidized beds, and membrane systems. BPNP is followed by an aeration process to promote aerobic biodegradation of assimilable organic (AOC) and biodegradable dissolved organic carbon (BDOC) in combination with a filtration process for turbidity removal. 3b.Physicochemical Technology Physicochemical drinking water treatment is frequently used in the area of drinking water treatment. This technique is applied to remove the heavy metals, oils and suspended matters. This physiochemical drinking water treatment technique is used to treat drinking water in order to become process water. According to (Spellman, 2009)the steps that are under this technique are coagulation, flocculation, sedimentation, filtration, disinfection and arsenic removal from drinking water. The coagulation process that occurs in this drinking water treatment technique will be discussed in details in this assignment. The definition of coagulation is the destabilization of colloidal particles.(L.Droste, 1997)The particles are coated with a chemically sticky layer that enables them to stick with each other, forming a large molecule and settle in a short period of time. The ability of an agent to agglomerate the tiny particles found in water is directly related to its charge. The other factor that will affect the ability is the size of synthetic polymers. The most common materials that are used to coagulate the water are alum (aluminum sulfate) and iron salts. (L.Droste, 1997) stated that the multivalent characteristic of these coagulants effectively attracts them to charged colloidal particles and their high insolubility helps to ensure their removal from the water to a high degree. When coagulant such as alum is being added into the water, a chemical reaction that produces positively charged will occur. This reaction will indirectly reduce the electrical charges of the particles and hence form a sticky substance which also known as floc. In this reaction, turbidity, color and microorganisms can be removed easily. The formation of floc is the primary step of coagulation process. For perfect efficiency, intimate, rapid mixing of the water must be done and coagulant must be present. After mixing, the water should be stirred slowly so that the particles can stick to each other forming a large molecule. According to (Spellman, 2009) , the factors that will affect the coagulation process are pH, turbidity, temperature, alkalinity and he use of polymers. The degree to which these factors affect coagulation process relies on the type of coagulant use. The condition of raw water, optimum pH to coagulate the water and other factors must be taken into account before making decision on which chemical to be used. According to(E.Manathan, 2009), the main advantage of using this technique is lower cost compared to biological treatment. It requires less worker force and able to settle the issues regarding toxic materials effectively. On the other hand, it has its disadvantage too, which is require careful operator control and use up huge amount of energy. 3c.Advanced Oxidation Process (AOPs) Advanced oxidation process (AOP) is an oxidation process which affects water treatment by generating a sufficient quantity of hydroxyl radicals.(Goi, 2005) Hydroxyl radicals (†¢ OH), are non-selective reactive species, helps to oxidize pollutants into mineral end-products, yielding CO2 and inorganic ions.This process can treat those organic pollutants with high chemical stability and low biodegradability which cannot be treated by conventional techniques. Basically, refractory compounds cannot be removed efficiently by conventional biological processes, but AOPs will do and help to improve the overall compound removal efficiency in water treatment. Refers to Figure3.1 in appendix 2, in biological systems, AOPs are used as pre- and post-treatment. The pre-treatment improve wastewater biological treatability by common microorganism whereas post-treatment is targeted on the contaminants removal which not completely done during the biological treatment. (Cesaro, et al., 2013) Organic contaminants such as halogenated hydrocarbons (trichloroethane, trichloroethylene), pentachlorophenol (PCP), detergents, pesticides, etc can be destroying by this process easily. Besides, the inorganic contaminants (cyanide, nitrite, and sulfide) can be oxidized by this process. Non-photochemical and photochemical methods are used to generating the OH radicals. These two methods are as shown as table below: Fenton system In Fenton system, hydrogen peroxide (H2O2) acts as an oxidation agent. When hydrogen peroxide presents in excess, Fe (II) oxidizes to Fe (III) within few seconds or minutes and hydroxyl radicals will be generated. The reactions are as shown as below: Fe2+ + H2O2 → Fe3+ + OH– +.OH The catalyst used in this process is iron salts which generate ferric ion, Fe2+as the Fenton’s reagent. Besides, ozone (UV-light) and transition metal salts are used.Mostly, ironsalts are used as transition metal salts. (Munter, 2001)Under the UV-radiation, the felton’s reagent undergoes oxidation processes that utilize activation of H2O2, has high efficiency to treat the hazardous organic pollutants that present in water. (Albert, 2010) Fenton reagent uses in wastewater treatment to convert the contaminants to harmless compound such as carbon dioxide and inorganic salts. This Fenton’s oxidation is the most efficient method in removing effluent toxidity and color compare to coagulation-flocculation process. It helps to decrease the rate of chemical oxygen demand (COD), aromatic compounds, and total polyphenols in the wastewater. However, Fenton process also can be combined with coagulation to reduce flocs settling time, amount of COD, and enhanced color removal. Photo-Fenton-type oxidation is a process when Fe3+ ions added to H2O2/UV process, resulted Fe (OH)2+ complex in pH3 condition. Fe3+ + H2O →Fe (OH)2+ + H+ Fe (OH)2+ ↔ Fe3+ + OH When Fe (OH)2+ will further decompose into .OH and Fe2+ ions with the presence of UV light. Fe(OH)2+hv→ Fe2+ + .OH This type of reaction very relies on UV irradiation to start up the .OH generation. Besides, this UV irradiation can mineralize organic pollutants completely. Efficiency of Fenton/Fenton-like reagents with UV irradiation can be increased by efficient use of light quanta and photo-reduction of ferric ion.(Munter, 2001) Photocatalytic oxidation Photocatalytic oxidation is an alternative AOP method which introduced high energy (photons of ultraviolet light,UV) into the treatment system. Besides that, it is a potentially green chemistry drinking water treatment process. Throughout the whole process, no reagents are added and only relatively harmless catalyst TiO2 and sunlight (source of UV) is needed. Solid titanium dioxide, TiO2 is used as the photocatalyst leading to chain reaction for the production of HO. free radicals. (E.Manathan, 2009) When the surface of TiO2 is irradiated with ultraviolet radiation, â€Å"holes† (h) are generated at sites where excited electrons (e) are produced: TiO2 +hv → TiO2 (h + e) The surface holes may take electrons from dissolved hydroxyl ion to produce reactive hydroxyl radicals on the TiO2 surface: TiO2 (h) + OH → OH. Refers to theFigure 3.2 in appendix 2, solar disinfection (SODIS) and solar photocatalytic disinfection (SPCDIS) are appropriate technologies for water disinfection of Cryptosporidium oocysts at household level. Cryptosporidium species are protozoan parasites that infect humans and causes diarrheal disease by the food-borne or waterborne routes. Cryptosporidium is capable to survive in the environment for long periods and even treated water is not guarantee to be safe from these infective parasites. Therefore, SODIS and SPCDIS are introduced to deactivate these microorganisms to reduce the risk of infection. SODIS and SPCDIS are both using the same method to reduce the oocyst viability. Both of them involve storing contaminated drinking water in transparent containers that are placed in direct sunlight before consumption.The disinfection effect of sunlight only occurs at temperatures exceeding 45 à ¢Ã¢â‚¬Å¾Ã†â€™. Therefore during cloudy conditions, this process may take a longer time to ensure the safety of the drinking water. Photocatalytic disinfection, SPCDIS uses the non-toxic photocatalyst, TiO2 to enhance and accelerate the inactivation rate of the parasites. For SPCDIS, the photocatalyst particles would have to be removed after solar exposure and before consumption. Due to this additional step, the probability of compliance within communities in developing countries is low and lead to the inefficiency of the treatment. In order to overcome this problem, this photocatalyst,TiO2 has been isolated onto some form of coated flexible insert, which would reside permanently within the SODIS reactor. Due to the effectiveness of the cheap, flexible insert coated with the non-toxic photocatalyst TiO2, the photocatalytic oxidation is recommended since it enhances the diminution of the oocyst viability by as much as 50%. 4.Conclusions The three technologies in treating contaminated drinking water used different methods to purify water. Each of them has advantages and disadvantages. They have faced respective challenges in terms of added research and development. Some of the common challenges are techniques for effective removal of emerging contaminants, synthetic chemicals and pesticides, as well as problems in dealing with spills of chemicals in navigable rivers and lastly the development of sustainable treatment. The challenge involving technological development is the needs of economic, appropriate, relevant and sustainable developing technology. (Ray Jain, 2011) In fact, three of the technologies can be combined to bring the greatest efficiency in water treatment process. For biological technology, the slow sand filtrationand perchlorate processes are discussed. The biological treatment is environmental friendly but the limitation of the processes are low effectiveness when the turbidity of water source is hi gh. For physicochemical technique, the method discussed is coagulation, one of the challenges it meets is large amount of energy consumption; whereas its future prospect could be get use of solar energy which is environment friendly. For AOPs, fentonand photocatalytic process are discussed. Both of the processes still need a further research about the fundamental concepts and reaction mechanism. It is because there are still much remain to be done in terms of maximizing its efficiency, by enhancing the performance-related properties of oxide materials. 5.References /abstract 1 /intro 2,3 *4+WHO *5+natural regulations *biological /physico 6,7,8 carson /aops9,10,11,12 /13,14,15,16,17,18 (6) /conclu19 1

Christmas The Very Word Brings Joy Essay

Variety is the spice of life. Life without feasts and celebrations is charm less and lifeless. So is true in case of school life. Without functions and celebrations school life becomes monotonous and uninteresting. Therefore, almost all the schools have certain annual functions such as, Annual Sport Where excellence is a habit So lets enjoy the stage breaking performance. School fete is one event students eagerly wait.. A very good Morning & Merry Christmas and welcome to one and all present here to join this eve, for join us. Kids, ladies and gentleman. We are feeling nice to meet you and see you on this holy occasion. We hope and assure that you will also feel nice in this musical and joyful atmosphere. So you are most welcome again. Enjoy all the joyful moments and sweet and soft music to make the moments unforgettable. Band is going to start this cheerful evening with holy and religious music. This occasion is very special to all of us so first some blessing prayers. After that for your guest of honor, for your welcome the band will present some cultural folk songs and dances. I am sure you all will completely lost in the heaven of musical feel and colour yourself in the colour of this incredible Christmas eve. To make this day memorable, joyful and cheerful a musical atmosphere created here. games stalls, many stalls of eatables n different kinds of rides have been arranged 2 mk dis day d most special one for u†¦ To make you energetic there are arrangements of snacks and soft drinks†¦ END :- At the end I would like 2 thank all the guests for making every single moment of dis fete d unforgettable and memorable one wid ur presence.. We hope you all enjoyed this beautiful day. Thanks for joining us and once again merry Christmas and happy New Year to one and all. May Jesus makes all your wishes come true†¦ thank you everyone thanks a lot†¦ Christmas is my favorite time of year. As a child, I loved the lights, the Christmas tree, the presents 🙂 As an adult, I still love the lights, the  music and the decorations†¦ The sky was dotted with a few fluffy clouds that looked like candy floss. All praise be to God for such a celestial and symphonious evening. An evening full of allure and amazement.

Placenta Previa

Placenta Previa High Risk Pregnancy Placenta previa occurs when an embryo implants itself in the lower uterus and the developing placenta thereby implants low in the uterus and covers the internal cervical os. The previa can be complete, which involves the placenta covering the internal cervical os completely, or partial, which involves only a portion of the placenta covering the cervical os. The diagnosis is of placenta previa is often made in the second trimester by ultrasonography testing and is monitored for placental migration away from the os which occurs with uterine growth.Placenta previa in the second trimester puts the client at risk for developing vasa previa and thought to be a result of inflammatory atrophic changes to the placenta. In the third trimester, placenta previa is the leading cause of painless bleeding leading to hemorrhage. The bleeding occurs as the placental attachment is disrupted from thinning of the area as the cervix and uterus prepare for labor. Due to the location of the placenta, the uterus is unable to contract to stop the flow of blood from the vessels.When bleeding occurs, Thrombin is released and stimulates uterine contractions, which thereby disrupt the placental attachment from the uterus even more, causing increased bleeding and can eventually lead to hemorrhage (Joy, 2012). The incidence of placenta previa is in approximately one in 200 pregnancies, has a mortality rate of 0. 03%. Common risk factors include previous placenta previa, previous cesarean births, suction curettage for miscarriage, carrying more than one baby, delivery of six or more pregnancies, and tobacco or substance abuse (Perry, Hockenberry, Lowdermilk, & Wilson, 2010).For first time pregnancies, placenta previa occurs in about 1 in 1,500 pregnancies but the risk for women who have had more than five pregnancies increases to about 5 in 100 pregnancies.References: J oy, S. M. (2012, June 5). Placenta Previa. Retrieved September 29, 2012, from Medscape: emedicine. medscape. com/article/262063-overview#a0104 Perry, S. E. , Hockenberry, M. J. , Lowdermilk, D. L. , & Wilson, D. (2010). Maternal Child Nursing Care. Maryland Heights, MO: Elsevier.

Police Powers And Responsibilities Act 2000 - 935 Words

The Police Powers and Responsibilities Act 2000 (Qld) was introduced in Queensland on the 23rd of March, presenting a significant simplification and codification of the law involving the police powers. Police Powers and Responsibilities Regulation 2012 (Qld) works concurrently with The Police Powers and Responsibilities Act to ultimately publicize the law to police officers and the public in regards to police powers. Together, these effectively outline the obligations and safeguards which must be met when performing police duties in Queensland. This essay will discuss the ways both the Police Powers and Responsibilities Act and Police Powers and Responsibilities Regulations codifies the powers of police and how they impose safeguards against the abuse of powers in relation to questioning suspects about criminal offences. Chapter 15 of the Police Powers and Responsibilities Act 2000 (Qld) outlines through codification the â€Å"Powers and Responsibilities Relating to Investigations and Questioning for Indictable Offences†. When operating an interview of questioning suspects about criminal offences, the requirements in chapter 15 relating to questioning suspects are there as safeguards against the abuse of police powers. According to the Police Powers and Responsibilities Bill 2000, the legislation had a number of purposes behind codifying the powers of police. These purposes were to consolidate and rationalize the powers and responsibilities police officers have for investigatingShow MoreRelatedWhite Power, Black Crime, And Racial Politics1511 Words   |  7 PagesWhite power, Black Crime, and Racial Politics Racial profiling has been in existence for many years. One defines racial profiling as a method law enforcement agencies use to determine whether a person may be a suspect of a criminal act. â€Å"Racial profiling and racial discrimination against blacks in criminal justice administration can date back into the late 1600’s.† (Staples 2011) This is when the court officials in Philadelphia authorized the police to take up any â€Å"Negro† seen â€Å"gadding about† withoutRead MoreCriminal Justice System1524 Words   |  7 Pagesreduce the crime and the fire of crime. In order to achieve this it is using different agencies and the major of them are the Police, Prosecution, Courts, Prisons and Probation. They all are operating in synchrony for achieving their legal responsibilities and particularly for reducing the level of crime. The aim of this essay specifically is to discuss the functions of the police and how they actually fit with the objectives of the Criminal Justice System as a whole. The Criminal Justice System is focusingRead MoreSecurity At G20 : Global Leaders, Governors, And International Delegates Convened At The Biggest Gathering Ever Held1100 Words   |  5 Pagesthe city witnessed an unprecedented security safety arrangements. This global platform attracted activists protest groups to voice their fears over major political, social environmental issues. Over 26 protest groups had registered with the police for peaceful action and demonstration during the event. As a result, Brisbane CBD was under complete lockdown with heavily fortified zones. [1] COMPLEXITY: The first step towards planning security at the G20 is assessing the potential risks concernsRead MoreReview : Bulsey And Anor V State Of Queensland1337 Words   |  6 Pagesheightens the need for officers to use their powers within the ‘confines of the law’ when ‘forcibly arrest[ing] and detaining’ a person as to preserve the right to personal liberty, for once this right is left in the power of any authority, to imprison arbitrarily whomever they suspect, ‘there would soon be an end of all other rights and immunities.’ II: Procedural History and Facts The first appellant (Bulsey) was placed on a list of suspects who police officer Detective Miles thought should beRead MoreThe Oath of Office and Code of Ethics Essay1301 Words   |  6 Pagesmany issues facing the criminal justice system. Some of these issues include police corruption, use of excessive and deadly force, pursuits, and deviance. The media influences public opinion and there is concern over the morality, and ethics of our public leaders. (DeShon, 2000) The criminal justice system has two neglected and important issues of integrity and truth; the oath of office and the code of ethics. (DeShon, 2000) In many agencies the impact these two issues have on our communities areRead MoreA Report On Saudi Electricity Company1017 Words   |  5 Pagesreformed in 2000 as a joint stock company with paid-up capital of 33 billion SAR ($8.8 billion). Three-quarter of its shares is belonging to the government and one-quarter owned by Saudi Aramco, the third largest crude oil compa ny in the world, and individual shareholders. SEC is the only company which delivers all power aspects from generation to customer services in Saudi Arabia. The total capacity of generating electric comes from the power plants of the SEC. In 2008, the total power generated capacityRead MoreThe Stephan Lawrence Case875 Words   |  3 Pagesthe police work by the leadership in order to eliminate the prejudice and ensuring fairness police policy. First of all, elimination of racism should be done among the police officers. It must be a challenge to promote anti-discriminatory practice enclosed in the legal framework (Dalal, 2012). The prevention and the recording of the racial incidents consist of encouraging the population to report any hate crime. Furthermore, the recruitment of the people from minorities group among the police forcesRead MoreA Research Study Of Two Conceptual And One Pedagogical Types Of Research Essay1732 Words   |  7 Pagesordinary college students that applied for $15.00 a day for 14 days. The intent was to explore the volatile dynamic between prisoners and prison officers that exist as well provide reform to the real world of officers training in correction (Blaas, 2000). Starting out the experiment was a setup prison setting to use volunteers by way of a newspaper posting for the Experiment. College students replied to the newspaper ad that was asking for volunteers for the study of what is known as the psychologicalRead MorePolice And Police Brutality1331 Words   |  6 Pagesquestioning if they will ever be safe in the streets again. Not everyone in the world is a criminal, but it only takes one person to ruin and blame the whole race. Police brutality is an everyday case and there has yet nothing to be done to help reduce nor stop the violence. Often people critic the duty and the responsibilities that a police officer has in this county. Their duty is far from just eating donuts and drinking coffee. The first thing someone does when they feel like their life or someone’sRead MoreEssay Drug Trafficking, Consequences, and Accountability1453 Words   |  6 PagesLatin American state is unique, as are the various citizens who inhabit them. As drug trafficking is a transnational force, Latin American governments often find themselves not only at odds with one another, but with larger political and economic powers such as the United States (U.S.). In addition, how many of these states have decided to address the illegal drug trafficking business, often through the use of armed force, have put them at odds with their respective citizens. Despite the continued